100W200W Small Vertical Wind Generator Wind Turbine Good For City Use Safe In Strong Wind

Main Features:

Product Description:

1. Low start up speed; high wind energy utilization; beautiful appearance; low vibration

2. Human friendly design, easy installation, maintenance and repair.

3. Precise injection molding blades together with the optimized design of aerodynamic contour and structure, the blades have such advantages: high utilization of wind energy which contributes to the annual energy output.

4.The generators, adopting patented permanent magnet rotor alternator,with a special kind of stator design, efficiently decrease resistance torque. Meanwhile, it makes the wind generators match the generators quite well and increase its reliability.

Applications Filed:

1. Residential power system

2. Street light power system

3. Telecom power system

4. Monitoring power system

The wind generator Installation Steps

·It is prohibited to assemble and install wind generators in rainy days.

1. The insulated current transmission wires: transmission lines are built in the iron pipe tower. The upper end is led out through the center bore of the wind generator flange,while the bottom end are led out from the pipe opening which is 30cm away from the ground. The section from the opening to the point which is 60cm beneath ground should be protected by iron pipes who’s O.D should be 17mm to 21mm. The underground paths of the transmission lines to the controller can make arrayed and covered with iron pipe or a plastic pipe.

2. The installation sequence of the wind generators can follow the steps as illustrated in figure 3.

2-1. Place the steel bracket on the ground; block up the flange joint to 1.3m.

2-2. Align the wind generator flange to the tower flange. Cut away insulating layer of current transmission wire end (which are to be connected with controller) for 10mm, then short circuit the exposed copper wires (screwed together)

3. The lifting of the wind generators and tower should be proceeded with the presence of skilled slinger and the security should be guaranteed. The tower’s stance should be executed on the basis of the relevant requirement of permanent construction.

4. After installation of tower and lightning protection is finished, use 500V meggar to measure insulating resistance between transmission lines and earth (earth wire can act as ground) in the case of not losing the short circuited leads of transmission lines, measurement should not be less than 5MΏ, otherwise, insulating layer may be crushed or damaged should be dealt with immediately.

Maintenance and Precautions

1. Wind generators often work at poor environment, thus please make sure to check regularly with your sight and hearing; check whether the tower is swaying or whether the cable is loose (using a telescope is also a good idea).

2. Timely inspection should be made after a heavy storm. If there is any problem, please put down the tower slowly for maintenance. With regard to the wind generators for streetlights, there should be electrician climbing the pole to check if there is any problem when wind generator have been short circuited and security protection measures prepared.

3. The free maintenance batteries should be kept externally clear.

4. Do not disassemble the equipment by yourself. Please contact sales department when the equipment is out of order

Guangzhou HY Energy Technology Limited Corp. is a high-tech manufacturer focused on design, production and application of high performance and reliable small wind turbine products. HYE factory was established in 2001 located in northern part of Guangzhou city, factory has 150 workers, and a 10 people R&D team dedicated in higher performance and reliability of HYE wind turbine. HYE owns 35 patent designs on wind turbine blade, slip ring, rotor structure, over-speed control system etc. Each and every component of HYE wind turbine is independently designed and manufactured in house. HYE factory owns advanced wind turbine quality testing equipments and a strict quality control system, all products will go through 22 quality control processes all in HYE factory facility. All products has certificated with CE, ETL, RoHS and ANAB.

With over 17 years experience in production and application of wind & solar hybrid power system, HY Energy has developed over 20 different application fields of wind and wind solar hybrid system such as residential grid-tie power system, residential off-grid power system, stand-alone wind solar hybrid street lighting, wind solar hybrid powered telecom tower, wind solar hybrid powered monitoring system etc. Most of these applications have been widely applied around world and enjoyed a good reputation by its system quality, reliability and professional pre-sales and after-sales service of HYE team. Furthermore, all components of each system solutions are either developed by HY Energy or customized and optimized by supporting vendor according to HYE wind turbine special features or some specific project, this could maximize the system power production and also improves reliability and compatibility of the system. Our engineering team could provide whole system design and full construction support base on your specific requirements. We believe soon you will benefit from our professionalism.